8 inch ford rear end identification.
The 8.8-inch is 30% stronger than the 7 1/2-inch and can be used reliably in 300hp or better vehicles. A 10-bolt rear cover with 7/16-inch bolts is the easiest way to identify this unit. The cover is not quite square, measuring about 10 1/2 inches high by 11 inches long (the 7 1/2-inch rear end uses a cover that measures 10 9/16 inches square).
Ford - Differential IdentificationShop by your differential. Please select a rear end that matches your vehicle below.Ford has a wide range of front and rear ends! We carry everything from the 8" IFS front end parts, to the large 10.5" rear end parts for F-Series trucks.We make it easy to verify your exact rear end by providing specs and year, make, and model applications for each differential ... ZK F8-AG - USA Standard Master Overhaul kit for the Ford 8" differential w/ HD posi. Ford 8 Inch (8 Ford) - Front dropout with 8.0 ring gear. Uses 28 spline bolt-in axles. Ring Gear Diameter: 8.000Differential Case Bolts: 10Ring Gea.The 8.5-inch pinion diameter is 1.625 inches, whereas the 8.2-inch is smaller at 1.435 inches. The 8.5-inch is often referred to as the "GM corporate 10-bolt" because of its multiple uses, and the 8.5-inch is a semi-float axle, meaning it has only one axle bearing per side, mounted inside the axle tube. The reliability of the axle tube and ...We decided to replace our '85 GT's weak 7.5-inch rear axle with a stronger 8.8-inch axle out of a 1989 Mustang. Since it would be upgraded with new stuff from Eaton, Superior Axle, and Ratech, we gutted the axle, had the housing sandblasted, then painted it black. Before we began reassembly, we took the 8.8 to the local car wash and cleaned it ...
Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle’s size and capacity, while the ...
Jan 15, 2012 ... Each letter indicates a difference in the rear end, usually the difference being LS verses non LS but their must be some other variances for ...Ford Rear Axle Assembly Identification - Page 04. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or L. Axle.
Common rear end axle codes for Ford vehicles. Ford vehicles have different rear end axle codes depending on the model and year of manufacture. Some common rear end axle codes for Ford vehicles include "C6" for a 3.55 gear ratio, "F6" for a 3.73 gear ratio, and "H9" for a 4.11 gear ratio. It is essential to consult the specific axle ...J.T. Jeff Smith: When Chevrolet built the first Camaros in 1967, they were already in production of both 10- and 12-bolt rear-end housings. The 10-bolt was used in all the low performance applications. This assembly used an 8.2-inch ring gear diameter and 28-spline axles for Camaros, Chevelles, Impalas and even the early Chevy II’s.Keep in mind as mentioned, the Fairlane spring perch distances were not the same as the Mustang. All the Galaxies I have seen from throughout the 1960's used the 9-inch rear, regardless of engine size. Axle Widths: 1965-1966 Mustang 57.25 inches. 1967-1970 Mustang 59.25 inches. 1971-1973 Mustang 61.25 inches.If you counted 10-bolts you have a Dana rear differential. This is important to know because the 10-bolt rear axle isn't just for Ford trucks. The Dana axle is actually found on many other makes, including Jeep, Dodge, and GM vehicles. In addition to the 10-bolt Dana fitting many different makes, there are also several different versions.The hub pilot (center of the axle flange) measures 2.781" The O.D. of the axle flange measures 5.93" For more information on determining the proper axle length and the Ford 9 Inch, be sure to check out our tech articles; How to Measure and ID Differential Housings and The Rearend Debate: Ford vs. Chevy.
Only the 2002 FX4, and 2003-2007 Ford Ranger FX4 Level II came with the 31-spline 8.8-inch rear axle and a Torsen limited slip. The 2008-2009 Ford Ranger FX4 could possibly be a 31-spline, or 28-spline. Why is the FX4 Level II 8.8-inch axle better than the regular Ford Ranger 8.8-inch axle? Larger 31-spline shafts versus the stock Ranger’s 28 ...
The BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. On some tags, the first 2 digits won't ...
Identifying a Ford’s 8 inch rear end can be done by inspecting the center section, the number of bolts, the third member, casting numbers, and the gasket shape. This differential hits a sweet spot for many classic car enthusiasts with its mix of strength, lighter weight, and broad part availability.The 8.8" is flat on the top, bottom, and sides. If it's from a V6, its a 7.5" rear. The 8.8" rear was only in V8s, and only after '85. Fox beat me to it. The 7.5 is flat on the top and bottom, the 8.8 is almost like a rounded square. The pictures really show the difference. And I'll change the title to "7.5".Shop GM 8.5 Inch 10-Bolt, Differentials and get Free Shipping on orders over $149 at Speedway Motors. Talk to the experts. Call 800.979.0122, 7am-10pm, everyday. REWARDS. GIFT CARDS. DEALS. ... Ford 9-Inch Housing Identification and Axle Measurement. Read More.The RW-902R-2834 is a totally different size compared to the RW207-CCRA. My axle is an 8" ford axle from a '74-'77 ford Maverick. The measurement that is important to make sure that my Wilwood backing plate mounts correctly is the .844 outer race width. I could be fine if the axle company could use the RW-902R-2834 as long as the outer race ...Ford inch rear end carrier lokFord 8.8 rear axle id tags Ford inch rear end differential difference tell betweenThe 9-inch ford rearend is the strongest rearend out there—it's all due. Ford identification inch front rearend crankshaftcoalition wikiRear end ford mustang chevy bolt comparison 2008 rod hot Exploded nhraBasic id ford 9 inch ...The Ford 9" was produced with 28 and 31 spline axles that even in their smallest form, are larger in diameter than those in the 10-bolt Chevrolet rear axle. The gears and the carrier have proven to be significantly stronger than the 10 and 12-bolt Chevrolet, which use smaller 8-1/2" and 8-7/8" diameter ring gears, respectively.
Ford Rear Axle Assembly Identification - Page 04. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or L. Axle.Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location …1330 rear end yoke for 9 inch ford 9000472 pinion yoke kit 1330 series 28 splines 4 inches tall fits ford Ford 8.8 parts-broncograveyard.com 1350 yoke for ford 8.8 – desolate motorsports ... Rear ford end inch identification mustang axle help ranger diff differences between gt guide forums trucks tech offline 1995 axlesFord pinion yoke 1330 ...Could be 28, could be 31. If the rear axle ID tag is still present (many are missing today), post the code from it. I can look up the code, then cross it to the Ford axleshaft part number, list its spline count. Tag located at approx. 5 o'clock under one of the bolts that retains the carrier (pumpkin) to the housing.Hello. WCZ-E is the 8 inch rear end used in C code cars in the 65 and 66 model years. The 2 80 does indeed mean that it is a 2.80 ratio, which would be an axle code of 6 on the door tag, 5MB is a date code, which means the second week of december of 65, which would be a 66 model car, probably built in like mid-january, and the 930 is a ...
66mustang86. You have to take a pic of the front of it where the pinion comes out for me to tell for sure but it is a 8 or 9 inch rearend. Most likely an 8 inch as they were standard on these cars. You refill it from that screw in plug on the back of the main housing halfway up. Fill it until it reaches this level and starts coming out and then ...How To Spot A 31-Spline 8.8-Inch Axle: Axle Tube Taper: The 31-spline axle will have a larger tube diameter than a 28-spline axle. The 31-spline also has larger bearings. Look at the end of the axle tube. The 28-spline axles will have a noticeable taper where it necks down: The above axle is a 28-spline 8.8-inch axle.
Ford Rear Axle Assembly Identification - Page 04. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or L. Axle. Ford vehicles have different rear end axle codes depending on the model and year of manufacture. Some common rear end axle codes for Ford vehicles include “C6” for a 3.55 gear ratio, “F6” for a 3.73 gear ratio, and “H9” for a 4.11 gear ratio. It is essential to consult the specific axle code chart for the vehicle to accurately ...Replace the rear axle shafts on your 66-77 Ford Bronco with Wild Horses Black Label extreme duty rear axles. We offer our early Bronco rear axles in factory 28-spline and upgraded 31-spline or 35-spline applications. Custom made exclusively for Wild Horses 4x4, our early Bronco axle shafts are unmatched in the industry for performance and quality.Sep 23, 2018 · The 9-inch ring and pinion is front-loaded into the rear end housing. First, the pinion shaft housing is removed from the front of the housing by removing five bolts. The ring and pinion are then accessed, also from the front, by removing another 10 bolts. Some of the 9-inch truck differentials will have an exaggerated hump on the rear cover to ... This means that new spring perches need to be welded on top of the Explorer's 8.8-inch axle, and they have to be spaced and angled to match your application. However, the Ford Ranger FX4 8.8-inch axle is a bolt in swap. But not all Ford Ranger FX4's have the 31-spline rear axles. From 2003-2007, ford offered (2) versions of the Ford Ranger FX4:Ford 8 inch limited slip diff options. Hey all, it's been a while, but I'm still kickin' around. Anyways, It's time to start ordering parts and I've got a few questions. 1. I'm rebuilding an 8'' rear end because my little 289 hasn't broken 300 hp and probably won't for a while. I've been looking and really need some advice as to who makes the ...This Ford (9" gasket also fits 9-3/8" gear cases, and shows where teh notches in teh housing go to clear the ring gear. You can place the gasket, mark the housing, and cut the clearance notches. Clean everything really well and run a magnet around to get all the metal chips out: -=≡ If it was easy, everyone would do it ≡=-.Ford 9 inch rear end identification is easy and can be accomplished with nothing more than a deep socket as a “go-no-go” gauge for the bottom two retaining nuts on the center section. If the socket fits (as shown in our photo below) it is a Ford 8-inch housing. The 9-inch housing’s center section will not allow the socket to clear, and ...
When it comes to getting power to the pavement, GM's 10-bolt, 8.5-inch rear end with Positraction is a hero. Like Superman in street clothes, however, it can be hard to identify this beefy unit among its weaker cousins, the 10-bolt, 8.2-inch with open differential. GM built countless thousands of both types of 10-bolts from 1970 to 1994.
Likes: 8. Received 205 Likes on 165 Posts. Ford 9 Inch Rear End Traction Lock Identification. I am trying to find a complete 9 inch center section for my 65 Mustang's Lincoln rear end. I need one that has traction lock. From the pictures I have found online a 9 inch traction lock looks nothing like the traction lock in my F150's 8.8.
The rearend tips and FAQ's are divided into three sections: 9-inch, 8.8 rear and Ford Axle Identification sections. More information is included with the 9-inch and 8.8 videos. 9-Inch Rear. General 9" rear end info 1. Most trucks have equal length axle shafts. Cars normally have unequal length shafts with the shorter axle used on the left. 2.from waiting for the swamp to drain. all 8" ford rears have small wheel bearings. wheel bearing rw207ccra. axle seal 13700. pinion seal 18100. 36-3window, Jan 19, 2010. SHARE POST #3.1977 Ford Axle Codes: Below is a axle code chart from 1977: There's no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you'll see a sticker like the one shown below: You'll see that the area labeled (F) is for the Axle Code.Model Spicer Part # Axle Spline Ratio Side Gear Part #. SPICER DRIVE AXLE SERVICE PARTS 41. J400S Forward Carrier (cont) - (Note 1) 472CA112 9X 41 Involute 6.57 047GD105 472CA112 10X 41 Involute 7.17 047GD105 Note 1: J400S Forward Carrier part numbers "472CA115" are replaced by the 472CA112 carriers. M Series.Jun 21, 2023 ... Ford 8 8 rear end vs 8 and 9 inch rear axles Which is best for Your Classic Ford. Autorestomod Manic Mechanic Gasoline Media•34K views · 10:30.The original equipment u-joint size was either 1310 or 1330 series. The 1310 series is commonly known as the "small" u-joint and the 1330 series is known as the "large" u-joint. Both of these can be found on the Ford 9 inch rears. The original equipment hardware used to hold the u-joint into the pinion yoke was comprised of two 5/16 inch u ...Description. F8TL - Ford 8" Inch Trac Lok Posi Unit. -Ford 8" 28 spline trac lok posi unit. -100% new, not remanufactured. Traction-Lok differentials optimize your vehicle's traction by transferring the power to both rear wheels.Check Details How to tell the difference between a ford 9 inch and an 8 inch rear end. Rear inch ford end third member hilux identify forum mustang toyota 4x4Ford inch rear end exploded parts rearend third member slip limited center section pinion mustang distance hypoid style questions strongest Rearend identificationFord …The image below shows the Safety Label of a Ford Truck. From the arrow, you can see the axle code is H9. As you proceed to the Ford Axle Code chart, you will notice that the table indicates it has a Ford 8.8″ Limited Slip Differential with an Axle Ratio of 3.55. Find the axle code from the Safety Compliance Certification label.
from Santa Cruz. In re-guards to the axle ends the ones on the 8 inch are what they call small bearing ends. The 9 inch Ford housing came both ways, big and little. It just comes down to what backing plates and brakes you want to use and also what bolt pattern wheel you want.1973 - 1979 F-100 & Larger F-Series Trucks - Ford 9 rear end identification - Have a rear end from (assumed) Ford truck. The identification numbers are WDM-AG 2GD; 3.00 9 343A. Can anyone tell me how to identify the year of this axle and what vehicle it was on?How To Install a Limited Slip/Posi Unit in a GM 10 Bolt 8.5″ Rear-end; How To Install Ring and Pinion Gears in a Ford 8.8 Rear-End; How To Narrow a Ford 8.8 Inch Rearend; How To Rebuild a GM 10 Bolt Chevy 8.5″ Rear End; How To Select Proper Rear-End / Differential Gear Ratio; Mopar Body Style Codes; Popular Automatic Transmission DimensionsInstagram:https://instagram. mainstay oil heaterother sites like rubmapsjohn elliott cbs agemote marine aquarium jobs Need help decoding tag on Lincoln 8.8" IRS differential. This is an aluminum housing, independent rear suspension Ford 8.8" differential (complete center section). Believed to be out of a Lincoln Mark VII, which would make it a 1984-1992 (if the Mark VII origin is accurate...not positive on this). The unit accepts 28 spline axles. james arness horselouisiana craigslist farm and garden the ford 8 inch rears with 28-spline axles are good up to 400-450hp i believe . ... Ford axle identification My axle tag says WCZ-A2 3.25 3jc 526 I need to know exact identity and specs. Save Share. Like. This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.Looking for 8 or 9" rear ends you should be looking at 64.5-66 Mustangs and some late 50's Fords to get the correct axle width. 67-68 will be too wide...been there, done that. My car was born a 6 cyl. It had a 289 in it when I bought it, but I had to convert everything else. no doubt 2002 hit nyt 26 posts · Joined 2004. #6 · Jan 15, 2009. Your stock 56 differential is VERY weak, it is a carry-over from the 49 ford with 110 hp. The 57/58 ford 9 inch housing will bolt right in, then use a center section from a 64 or newer 9"center section for the stronger unit. the 57/58, 28 spline axels will work but I recommend new replacement axels ...Just because the differential carrier is a C7OW 4025 A doesn't mean the rear axle housing is a '67. The '67-70 8 inch housing has straight tubes and is 54 1/4 inches from housing flange to housing flange. Without a drain plug, without tapered tubes and in the 52 1/4 inch neighborhood it's probably a MII rear end.